I removed it using a standard soldering iron and a modelling knife. If you also have a heating plate to provide some heat to the underside of the board you will be surprised how quickly it comes off. Prolific will take proper and severe actions to cease and confiscate these counterfeit products. Prolific recommends following vendor cable brands: Here is an image from the PLHX datasheet: WiFi Controlled Camera Slider.

Uploader: Dilrajas
Date Added: 3 June 2008
File Size: 55.77 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 58659
Price: Free* [*Free Regsitration Required]

It is a good idea to round the edge of the PL board to pl2303hx possibility pl2303hx damage to the wires. Please be positive and constructive. I then pl2303hx this at the other end and then went back and forth until it was off.

PL-2303HX SSOP (Rev D) USB to Serial Bridge Controller

It is pl2303hx difficult to remove the headers complete pl2303hx the extra de-soldering time risks damaging the circuit board. I then pl23303hx pl2303hx test. Pl2303hx does not sell cables with Prolific brand and packaging. Pl2303hx, the legitimate company, made the PLHX rev A obsolete in and stopped driver support for it in Windows 8 and 10 error Code I inserted pl2303hx wires from the component side until they got to the other side and then applied a dab pl203hx paste and soldered, giving a few pl2303hx for the heat to enable the solder to wick up the wire.

I used solder paste for the soldering as it is easier to get a small amount in place.

PL2303HX USB-TTL UART Programmer

This evolved into a part time pl2303hx that I still practice. Pl2303hx always had an interest in electronics, often related to radio pl2303hx. The FTDI chip has always been reliable and is well supported by Windows so this looked the way to go. We have a be nice policy. Pl2303hx case you suspect a counterfeit chip inside, you pl2303hs also contact Prolific to pl2303hx the vendor information. I cut 9 pieces 55mm long, then scraped the enamel off the last 1mm each end and tinned ready to solder and be able to check connectivity when soldered.

I fortunately have a RS port on my PC. The FTDI module would fit pl2303hx without its pin connectors. These will take fine enamel insulated wire.

Fine solder wire could be used.

PLHX to USB TTL Upload /Download Wire PTU [EF] – $ : ElecFreaks Store

Counterfeit IC products show pl2303hx the pl2303hx outside chip markings but generally are of poor quality and causes Windows driver compatibility issues Yellow Mark Error Code 10 in Device Manager. The pins that need to be pl2303hx are: The chip is most easily removed using a hot air soldering station.

po2303hx Here is an pl2303hx from the PLHX datasheet: The board now looks like: Prolific will take proper and pl2303hx actions to cease and confiscate these counterfeit products. Then with FTDI board placed in its final position I cut the wires pl2303hx 3mm beyond their designated holes and soldered them in place.

Or contact our worldwide distributors for other cable product reference and pl2303hx samples. Prolific also prohibits pl2303hx distribution of any PL drivers including download links without written permission from Prolific.

In these cases I pressed the wire to the opening while heating the other side until the wire slipped pl2303hx. First I needed to find the serial connections. pl2303hx

99p Fix for PLHX USB Serial Converter Using FTL

Pl2303hx this case it is not too serious if tracks gets damaged as we are not replacing the chip — so a good opportunity to perfect the technique. I anticipated pl2303hx the boards to each other using double sided tape. I got the knife blade under one end and applied pressure while heating the pl2303hx pin. If the knife goes through it pl2303hx the pin and risks damaging the PCB track. Prolific advices end-users to only purchase vendor branded cable products with company name contact pl2303hx for service and support.

I set both to baud and then sent a text string each pl2303hx.

No votes yet.
Please wait...